BalZout Electronics Mounts - $139.99 to $165.00
Some of the toughest mounts money can buy - the BalZout Electronics Mounts are 100% made in the USA. The sturdy, connecting arms are made from cnc-machined, anodized, aircraft-grade aluminum, and the balls that make the mounts work, as well as, the threaded studs are made from stainless steel. The holes in the knobs also allow you to use the end of whatever is handy to lock them down. That means you don't have to stop half way to your next hot spot and reposition your graph to keep it from beating a hole in your deck or knocking the gel coat off the counsel. Rest assured the BalZout Electronics Mounts are strong enough to stand up to the abuse, the knobs are made in Missouri, the studs are made in New York, and BalZout makes the rest.
Proudly Made in the USA
|Large Mount Round||6-7/8" x 1-3/4"||8-3/4"||3-3/4" Diam.|
|Large Mount Square||6-7/8" x 1-3/4"||8-3/4"||3" x 3"|
|Small Mount Square||4" x 3-1/2"||7-3/4"||3" x 3"|
Humminbird 700-series and below - Small Mount
Humminbird 800-series and above - Large Mount
Lowrance HDS-8 and above - Large Mount
Comments: I cannot tell you how great these things are, we recently installed a HDS 10 on the console of our boat and this thing is solid as a rock. They could charge 3 or 4 hundred dollars for these things and I would buy them again in a heartbeat, after having two other (small) ram mounts break under the minimal weight of a HDS 5 I knew I didn't want a $3000 unit being held above the water by a slightly beefed up version of the same technology (which seems to lose all structural integrity when the weather dips below about 20 degrees). After having it on the boat for a couple months I can say without a doubt that if your graph IS somehow jarred loose from it's original position with this mount, than you are going to have much bigger problems than losing a graph. Bottom line when the ram mounts on my front graphs finally give way (which shouldn't be to long now) I'll be purchasing a couple more of these to go up front and never have to adjust them after going over 2 foot rollers again.
From: Jake: SC 3/18/14
Comments: when the new boat comes in in a week I will put the two on I purchased (have rams on current boat). Look really good and well built. Hopefully the stand up to st. Clair and Erie better than the POS ram mounts... Looks like they are going to be a must have for the GL fishing crowd.
Comments: Just installed them on my Basscat. I love them no more having to adjusting units. I have a HDS 12 and HDS 10 they work perfect!!!
From: Tyler: AL
Comments: I have bought the large mount balzout and love it i had other mounts and nothing compares to the balzout.
From: Justin: Heber springs ar
Comments: Put a BALZOUT on my boat finally someone made a quality mount for my $2k graph no more bouncing off the console while running anymore like my ram mount. Which I threw in the trash. Prob could of sold it but didn't want to be liable for someone else's graph to hit the console. You get what you pay for should of known better than going cheap on a ram. Lesson learned don't make the same mistake as me.
From: Jesse: Paris, MO
Comments: Mounted Elite-7HDI on the bow with large mount. Set it and forget it does not move even under the roughest conditions. No more Ram Mounts for me.
From: Bill: Spartanburg, SC
Comments: fyi if your existing unit is mounted on the side of your counsel it can be tough to get the balzout mount level. I had to create a shim to get the base level. for sure ten times as sturdy as other mounts on the market but only a quarter of the position options
From: Brian: Wauconda, IL
Comments: Best Mount made, No more having to adjust mount when running in ruff water. Unit stay exactly where you put it no matter how ruff of water.
From: Ryan: St. Charles, MO
***Note: If you have questions about this product or need assistance with an order please email your questions to email@example.com